Return to BSD News archive
Path: euryale.cc.adfa.oz.au!newshost.carno.net.au!harbinger.cc.monash.edu.au!news.rmit.EDU.AU!news.unimelb.EDU.AU!munnari.OZ.AU!news.ecn.uoknor.edu!feed1.news.erols.com!howland.erols.net!newsfeed.internetmci.com!in2.uu.net!umcc.umich.edu!umcc.umcc.umich.edu!kli
From: kli@umcc.umcc.umich.edu (Kelvin Li)
Newsgroups: comp.unix.bsd.freebsd.misc
Subject: ATAPI CDROM Help needed: "atapi0.1: unknown phase"
Date: 27 Oct 1996 19:16:55 GMT
Organization: UMCC, Ann Arbor, MI, USA
Lines: 122
Message-ID: <550cf7$9ka@umcc.umcc.umich.edu>
NNTP-Posting-Host: umcc.umcc.umich.edu
X-Newsreader: TIN [version 1.2 PL2]
I'm still having trouble getting my IDE CDROM to become a device that I
can mount. Does anyone know what I need to do when I get this message on
startup?
wdc0: unit 1 (atapi): <NEC CD-ROM DRIVE:282/3.04>, removable, dma, iordy
atapi0.1: unknown phase
Enclosed below this message is the rest of the "dmesg" output in case it
helps!
As far as I can tell, i have both IDE Hard Disk and CDROM on the same
controller configured correctly. The original setup was HD on controller
0, and CDROM on controller 1. I moved the CDROM to controller 0, and
jumpered it as a slave. I'm assuming that the HD is a master because NT
and DOS still recognize them when I dual boot.
Should I include my kernel configuation file???
Thanks for any help!
Kelvin
dmesg output:
------------------------------------------------------------------------------
FreeBSD 2.1.5-RELEASE #0: Fri Oct 18 00:32:17 1996
root@myname.my.domain:/usr/src/sys/compile/MYKERNEL
CPU: 133-MHz Pentium 735\\90 or 815\\100 (Pentium-class CPU)
Origin = "GenuineIntel" Id = 0x52c Stepping=12
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 33554432 (32768K bytes)
avail memory = 30547968 (29832K bytes)
pcibus_setup(1): mode1res=0x80000000 (0x80000000), mode2res=0xff (0x0e)
pcibus_setup(2): mode1res=0x80000000 (0x80000000)
pcibus_check: device 0 is there (id=122d8086)
Probing for devices on PCI bus 0:
configuration mode 1 allows 32 devices.
chip0 <Intel 82437 PCI cache memory controller> rev 2 on pci0:0
CPU Inactivity timer: clocks
Peer Concurrency: disabled
CPU-to-PCI Write Bursting: enabled
PCI Streaming: enabled
Bus Concurrency: enabled
Cache: 256K pipelined-burst secondary; L1 enabled
DRAM: no memory hole, 66 MHz refresh
Read burst timing: x-2-2-2/x-3-3-3
Write burst timing: x-3-3-3
RAS-CAS delay: 3 clocks
chip1 <Intel 82371 PCI-ISA bridge> rev 2 on pci0:7:0
I/O Recovery Timing: 8-bit 3 clocks, 16-bit 2 clocks
Extended BIOS: disabled
Lower BIOS: disabled
Coprocessor IRQ13: enabled
Mouse IRQ12: disabled
Interrupt Routing: A: disabled, B: disabled, C: disabled, D: disabled
MB0: disabled, MB1:
chip2 <Intel 82371 Bus-master IDE controller> rev 2 on pci0:7:1
mapreg[20] type=1 addr=0000ffa0 size=0010.
I/O Base Address: %#lx
Primary IDE: enabled
Secondary IDE: disabled
vga0 <VGA-compatible display device> rev 0 int a irq 11 on pci0:16
mapreg[10] type=0 addr=ff000000 size=800000.
pci0: uses 8388608 bytes of memory from ff000000 upto ff7fffff.
pci0: uses 16 bytes of I/O space from ffa0 upto ffaf.
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x280
ed1 not found at 0x300
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
sio2: disabled, not probed.
sio3: disabled, not probed.
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
lpt1 not found at 0xffffffff
psm0 at 0x60-0x63 irq 12 on motherboard
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <WDC AC21000H>
wd0: 1033MB (2116800 sectors), 2100 cyls, 16 heads, 63 S/T, 512 B/S
wdc0: unit 1 (atapi): <NEC CD-ROM DRIVE:282/3.04>, removable, dma, iordy
atapi0.1: unknown phase
wdc1 not found at 0x170
sea0 not found
wt0 not found at 0x300
mcd0: timeout getting status
mcd0 not found at 0x300
matcdc0 not found at 0x230
scd0 not found at 0x230
1 3C5x9 board(s) on ISA found at 0x300
ep0 at 0x300-0x30f irq 10 on isa
ep0: utp[*UTP*] address 00:c0:4f:d7:4f:77
lnc0 not found at 0x280
npx0 on motherboard
npx0: INT 16 interface
sb0 at 0x220 irq 7 drq 1 on isa
sb0: <SoundBlaster 16 4.13>
sbmidi0 not found at 0x330
Device configuration finished.
Considering FFS root f/s.
Configuring root and swap devs.
configure() finished.
BIOS Geometries:
0:020b3f3f 0..523=524 cylinders, 0..63=64 heads, 1..63=63 sectors
1:01300311 0..304=305 cylinders, 0..3=4 heads, 1..17=17 sectors
0 accounted for
wd0s1: type 0x6, start 63, end = 822527, size 822465 : OK
wd0s2: type 0xa5, start 822528, end = 2048255, size 1225728 : OK
wd0s3: type 0xa5, start 2048256, end = 2116799, size 68544 : OK
fd0c: hard error writing fsbn 4 of 4-6 (ST0 40<abnrml> ST1 2<write_protect> ST2 0 cyl 0 hd 0 sec 5)
fd0c: hard error writing fsbn 13 of 13-15 (ST0 40<abnrml> ST1 2<write_protect> ST2 0 cyl 0 hd 0 sec 14)
fd0c: hard error writing fsbn 1531 (ST0 40<abnrml> ST1 2<write_protect> ST2 0 cyl 42 hd 1 sec 2)